Latest Posts

  • Lambda szonda hibák 2012-04-04 10:11:21 Egy elég általános szakmai hibáról szeretnék írni nektek. Hibakódolvasókat használók körében, de leggyakrabban a kezd?k körében minden napos...
  • Ford hibakódok P2336 2012-04-04 09:51:04 Fordoknál sokan nem tudják mire vélni az alábbi hibakódokat, és nem tudják mi a teendö. P2336 - (1-es henger, kopogási küszöbérték felett)...
  • P0172 Túl dús keverék (1-es hengersor) 2012-04-03 20:44:25 P0172 Túl dús keverék (1-es hengersor)? Vesézzük csak ki egy kicsit, hogy mit is jelent pontosan ez a hibakód és mik okozhatnak dús keveréket....
  • P0171 Túl szegény keverék (1-es... 2012-04-03 20:38:55 P0171 Túl szegény keverék (1-es hengersor)? Vesézzük csak ki egy kicsit, hogy mit is jelent pontosan ez a hibakód és mik okozhatnak szegény...
view all

Népszerű eladások

Megtekintett termékek

Új termékek

Renault immobilizer emulator MSA15 SiriuS32 Fenix5

Új termék

Renault immobilizer emulator MSA15 SiriuS32 Fenix5

Bővebb leírás

6,900 Ft Adóval

Egyéb infó

Specification:
After decoding of Renault injection computer using RENAULT RESET TOOL or by entering security code, in most cases you can start engine, but some of injection computers can not operate without immobilizer code stored in their memory. Diesel EDC15C3, DCU3R and MSA15, petrol SIRIUS32 (except those for 1.4Lengine) and FENIX5 for 2.0L 16V engine require working unlocked (with good key) immobilizer unit or Renault immobilizer emulator. Use together withRENAULT ECU DECODER for a complete kit.
 All Renault models, fitted with single-data-wire coded immobilizers. I.E.from 1994 approx. until the introduction of CAN (2001 to 2003, dependingon exact model).
Immo pin code is not required
Decode the ecu using the renualt ecu decoder.
Only 3 wires to connect: Ignition, Ground and Data.
 
Small module size
Module is designed to be left permanently connected to the car.
Non-volatile memory means no data loss, even after flat batteries or jump startS.
Module can be used again if need be.
As the name suggests, the Emulator Module is capable of emulating an immobilizer data stream to the ecu. It can do this every time ignition is turned on,
meaning that you have a car which simply starts, even just using a steel (non electronic) key.
Note that once the module is fitted to a car, the original equipment immobilizer is effectively disabled.ou need to make your customer aware of this, so that they can arrange to fit an alternative deviceas required.
 
For Petrol ECU's
For SIEMENS FENIX3B
For SIEMENS FENIX5
For SIEMENS SIRIUS32
For SAGEM SAFIR (55pin)
For SAGEM SAFIR2 (35pin)
For BOSCH MOTRONIC MP7.0
For MAGNETI MARELLI IAW 06R
For MAGNETI MARELLI IAW 8R.30
For Diesel ECU's
For BOSCH MSA15.5 (DTI)
For BOSCH EDC15C3 (DCI)
For LUCAS DCU3R (1.9D)
For Coded fuel cut-off valve (1.9D DDS)
 
Features:
The engine ECU won’t run the engine until it receives a coded message (a ‘unique’ number) from the immobilizer. The ‘unique’ part means that every immobilizer is different,
and so swapping immobilizers won’t help get a car running. There is no starter motor cut on Renault models. The immobilizer may be a stand alone unit, or it maybe built in to a larger control unit.
Once the ecu has been decoded, the emulator should be fitted as shown, this can be done direct to the ecu or along the immobilizer wiring loom.
After connecting the emulator cut the immobilizer line from the immobilizer unit as shown.
 
Fitting Process:
1. Ensure that the ecu has been decoded. This can be done with the Renault ecu decoder
2. Connect the module to the car’s wiring harness: Red wire to ignition feed, black wire to earth, and yellow wire to the data wire
3. Cut the wire to the immobilizer, so that the module is connected directly to the engine ECU, and the immobilizer is out of the circuit.
4. Turn ignition back on, the car should now start.

Vélemények

Írd meg véleményed

Renault immobilizer emulator MSA15 SiriuS32 Fenix5

Renault immobilizer emulator MSA15 SiriuS32 Fenix5

Renault immobilizer emulator MSA15 SiriuS32 Fenix5